Brocade Mobility RFS Controller System Reference Guide (Su Bedienungsanleitung PDF herunterladen (Seite 94)

100

101

82 Brocade Mobility RFS Controller System Reference Guide

53-1003099-01

6. Optionally define the following Cluster Settings and overrides:

7. Wi th i n t he Cluster Member field, select Cluster VLAN to enable a spinner control to designate

the VLAN where cluster members are reachable. Specify a VLAN from 1 - 4094.

Specify the IP addresses of the VLAN’s cluster members using the IP Address table.

8. Select OK to save the changes and overrides made to the profile’s cluster configuration. Select

Reset to revert to the last saved configuration.

Access Point Radio Power Overrides (Access Points Only)

A profile can manage the transmit output power of the Access Point radios it supports within the

network.

Cluster Mode

A member can be in either an Active or Standby mode. All active member

controllers or service platforms can adopt Access Points. Standby members only

adopt Access Points when an active member has failed or sees an Access Point

that’s not yet adopted. The default cluster mode is Active and enabled for use

with the profile.

Cluster Name

Define a name for the cluster name unique to its configuration or profile support

requirements. The name cannot exceed 64 characters.

Master Priority

Set a priority value from 1 and 255 with the higher value being given higher

priority. This configuration is the device’s priority to become cluster master. In

cluster environment one device from cluster members is elected as cluster

master. This configuration is the device’s priority to become cluster master. The

default value is 128.

Handle STP Convergence

Select the radio button to enable Spanning Tree Protocol (STP) convergence for

the controller or service platform. In general, this protocol is enabled in layer 2

networks to prevent network looping. Spanning Tree is a network layer protocol

that ensures a loop-free topology in a mesh network of inter-connected layer 2

controller or service platform. The spanning tree protocol disables redundant

connections and uses the least costly path to maintain a connection between

any two controllers or service platforms in the network. If enabled, the network

forwards data only after STP convergence. Enabling STP convergence delays the

redundancy state machine execution until the STP convergence is completed

(the standard protocol value for STP convergence is 50 seconds). Delaying the

state machine is important to load balance APs at startup. The default setting is

disabled.

Force Configured State

Select the radio button to allow this controller or service platform to take over for

an active member if it were to fail. A standby controller or service platform in the

cluster takes over APs adopted by the failed active member. If the failed active

member were to come back up, the active member starts a timer based on the

Auto Revert Delay interval. At the expiration of the Auto Revert Delay, the standby

member releases all adopted APs and goes back to a monitoring mode. The Auto

Revert Delay timer is stopped and restarted if the active member goes down and

comes up during the Auto Revert Delay interval. The default value is disabled.

Force Configured State

Delay

Specify a delay interval in minutes (1 - 1,800). This is the interval a standby

member waits before releasing adopted APs and goes back to a monitoring

mode when an active cluster member becomes active again after a failure. The

default interval is 5 minutes.

1 2 ... 89 90 91 92 93 94 95 96 97 98 99 100 101

Modelle	Dokumententyp
ZKS651DX	Bedienungsanleitung ZANUSSI ZKS651DX Benutzerhandbuch [en] , 40 Seiten
ZKL64X	Bedienungsanleitung ZANUSSI ZKL64N Benutzerhandbuch, 24 Seiten
ZUQ875N	Bedienungsanleitung ZANUSSI ZUQ875N User Manual, 48 Seiten
ZKF641F	Bedienungsanleitung ZANUSSI ZKF641F Benutzerhandbuch, 20 Seiten
ZVM640X	Bedienungsanleitung ZANUSSI ZVM640N Handleiding, 24 Seiten
ZUQ875N	Bedienungsanleitung ZANUSSI ZUQ875X User Manual, 48 Seiten
ZOD685X	Bedienungsanleitung ZANUSSI ZOD685X User Manual, 48 Seiten
ZXE64BV	Bedienungsanleitung ZANUSSI ZXE64BV Benutzerhandbuch [fr] , 36 Seiten
ZKT623LBV	Bedienungsanleitung ZANUSSI ZKT623LBV Benutzerhandbuch [en] , 24 Seiten
ZOD370X	Bedienungsanleitung ZANUSSI ZOD370W User Manual, 28 Seiten
ZKH 863LX ZAN/HIC-8	Bedienungsanleitung ZANUSSI ZKH 863LX ZAN/HIC-8 Benutzerhandbuch [en] , 40 Seiten
ZCM7701XN	Bedienungsanleitung ZANUSSI ZCM7701XN User Manual [fr] , 40 Seiten
ZCM7901XN	Bedienungsanleitung ZANUSSI ZCM7901XN User Manual, 40 Seiten
ZC6675X	Bedienungsanleitung ZANUSSI ZC6675X Benutzerhandbuch, 28 Seiten
ZW5540	Bedienungsanleitung ZANUSSI ZXT5050 User Manual, 8 Seiten
ZOB30601XU	Bedienungsanleitung ZANUSSI ZOB30601XU Benutzerhandbuch, 24 Seiten
ZK630F 98P	Bedienungsanleitung ZANUSSI ZK630F 98P Benutzerhandbuch, 20 Seiten
ZKT350BV	Bedienungsanleitung ZANUSSI ZKT350BV Benutzerhandbuch, 32 Seiten
ZHF865C	Bedienungsanleitung ZANUSSI ZHF865G User Manual, 52 Seiten
ZME2002J	Bedienungsanleitung ZANUSSI ZME2002J Benutzerhandbuch [pl] , 20 Seiten

Brocade Mobility RFS Controller System Reference Guide (Su Bedienungsanleitung Seite 94

Kommentare zu diesen Handbüchern

Zanussi ZIT649BV Handbücher

Zanussi ZIT649BV Bedienungsanleitung (28 Seiten)

Inhaltsverzeichnis

Weitere Produkte und Handbücher für Öfen Zanussi